Paco Kelly's Leverguns.com

Sigmar

olyinaz wrote:
Terry Murbach wrote:YOU GOTTA BE KIDDING ALL OF US !!! YEEEEEEE GADS......WHATTA WASTE OF BANDWIDTH.
What? "90mm recoilless rifle vs. Red Rider BB gun - what should I buy?" It seems very straight forward to me!!

would be if it was for hunting only, leaning to defense

Sigmar

Buffalo Bore makes some fine hunting .45acp if you know your limitations....The 255 grain, flatnose, hardcast comes to mind.....I recall a test where these penetrated over twice as far as FMJ 230s.....My limitations would be fifty yards, at which range these would only drop about 2 inches 8) https:...

Sigmar

Hmmm.... you've got the world's premier hunting revolver cartridge in hand and you are considering acquiring the world's premier handgun self-defense cartridge. And you don't have room for one of each? You're kidding us, arentcha Sigmar? more an issue of funds otherwise yes it would be a no brainer

Sigmar

always been a wheelgun kind of guy hence my hesitation. but yes this choice is mainly with self defense in mind and I see the answer on the horizon.

Sigmar

which and why ? really thinking of trading in my casull but kinda cringing at the same time. It will be one or the other.

Sigmar

http://shivakicustomknives.com/

Sigmar

Very nice

Sigmar

Talking about commercial stuff. Differences, pros n cons ?

Sigmar

nice job ! i have some old worn out forrest blades laying around, may give this a try

Sigmar

Y'all are retired too huh

Sigmar

thanks, as usual y'all come through. any problems with these scopes on AR platform rifles holding zero? ie 308

Sigmar

game keeper wrote:I have tried without success, to find out what happened to all the guns that came over from the USA. I remember seeing photos in a magazine of crates of all kinds of civilian firearms sent over by American citizens in 1940.

bottom of the sea

Sigmar

finally found a nib DPMS LR 308. Now time for optics and more ignorant questions. I want to go with a variable low end mag no more than 4, with that in mind how high is the top end, only 12 ?

Sigmar

Thanks guys, thats what I've always been taught, doesn't hurt to verify again

Sigmar

BlaineG wrote:
Sigmar wrote:looked at em, was expensive, built my own for a quarter of the price. keeps a two car garage thats been converted into a wood shop relatively dust free
Ok....Please start a thread and elaborate...

I'll post the link that I used shortly

Sigmar

looks great to me, I'd buy a set

Sigmar

I have always been told 223 is fine out of a 556 barrel but not the other way around, headspace I think is the reason. However today I'm in a local gunshop where the owner is a "gunsmith", he says baloney. You can shoot a 556 out of a 223. So when I got home I pulled out my calipers and me...

Sigmar

looked at em, was expensive, built my own for a quarter of the price. keeps a two car garage thats been converted into a wood shop relatively dust free

Sigmar

YAAAAAWHOOOOOOOO ! Daughter is in labor with 1st grandchild,,,packing

Sigmar

fantastic video, thanks for sharing. Can't believe OSHA ain't all over them

Sigmar

Thanks much for the reply. will post pics when I'm done, well as long as y'all can handle looking at a new remlin

Sigmar

Great find. been looking for something pre 70 down here

Sigmar

BlaineG wrote:Looks like a top notch outfit....I bookmarked the site for later.....

+ 1

Sigmar

As per another thread that you had commented on this is what I'm doing with mine. Now for another ignorant question, do you cold blue the whole piece or just where you exposed fresh metal ? Also on removing the sight inside the dovetail it exposed fresh metal so I guess that will have to be touched ...

Sigmar

"because shaved lead jammed the cylinder" Is it aligning correctly?

Sigmar

bet the same arguments were made when the compound came out

Sigmar

You really didn't need to post this, my wifes gonna be upset to find out I'm thinking of getting back into reloading after reading this.

Sigmar

Tap the rear barrel sight out of it's dovetail slot so that it exits the barrel on the same side as the loading port (RH side). Please don't leave an empty slot - either buy a commercial slot filler blank, or make one out of an old longleaf rear sight. Here's the photo tutorial, on how to fashion y...

Sigmar

mikld wrote:Hmmm, too bad it's Remington ammo...

At this point I couldn't care who made it

Sigmar

k screws supplied worked and install is as simple as it gets. Now how do I remove the dovetailed? rear sight, looking down the barrel from the stock do I tap it out right to left or the other way ? I know I'm making this harder than it seems from my end, just want it to be right

Sigmar

FP-336 is the top mount Foolproof, FP-94/36 is the side-mount. All 336s after about 1952 are D&T. If yours hasn't got the two little 6-48 holes on the left side of the receiver then you need the FP-336. If you don't have the waffle-top 336 (so-called for the wavy matting on the top of the recei...

Sigmar

side eject if that makes any difference, nib just bought so new model. does have pre drilled top mount holes , just hope they are the same size as the screws provided with the sight. which loctight should i use ?

Sigmar

well based on recommendations from you guys I settled on a peep sight. Just got it in today and from reading the instructions its talking about tapping for the mounting screws. No haven't yet looked at my rifle (Marlin 336 30-30) almost afraid to find out this is true. Is it?

Sigmar

Marlin 336 30-30 and AR 223/556

Sigmar

Initial sight in at 25 yards will put you on paper at 100. If you're shooting nickel groups at 25 what would the groups be at say 100 ?

Sigmar

Been reading Patriots ?

Sigmar

Well I had a chance to look through some peep sights and due to eye sight they're not going to work, too blurry at the rear sight. So scope it will be. Bought a pic rail for it to mount a scope, haven't decided which scope yet. My ignorant question for the day is this. The screws in the top of the r...

Sigmar

so much for my question :roll: well, I guess if you have a use for zinc bullets, you could make them out of pennies. Probably still illegal (destroying currency) if you worry about such things. I think copper would stick to your bullet mold, as it melts at a much higher temp than zinc and lead allo...

Sigmar

so much for my question

Sigmar

Thunder50 wrote:With the proper dies, you might be able to "draw" the copper pennies, to make a bullet jacket, and then swage a bullet with the appropriate caliber dies.

what about solid ball made from them as you would lead?

Sigmar

what about pre-1983 pennies, were made of 95% copper and 5% zinc.

Sigmar

Since I'm known for stupid questions here goes another one. However this was asked of me and I didn't have an answer. Can you mold bullets out of pennies ?

Sigmar

to wake up another day and own a A10 308

Sigmar

I feel all warm and fuzzy about my 454 now

Sigmar

I shot mine for the 1st time last weekend. The grip that came with it is a crimson trace lazer grip. I found that the knuckle of my middle finger rests right against the trigger guard which made it very uncomfortable to shoot. Anyone else own one that can recommend a different grip to look at for la...

Sigmar

Do like my SRH 454 which also fires the 45LC. But need to do something about the grips as my middle finger knuckle rests against the trigger guard. A bit jarring with the 454 loads.

Sigmar

I have owned several .44 in both Blackhawk and Redhawk. Imho sturdiest gun ever built for reloaders. I'm partial to the .44

Sigmar

Anyone know what type of finish Marlin uses now on their stocks ?

Sigmar

The ammo sit rep in NY is similar. 22 LR and 22 mag are extinct. 9mm ball and better quality .357, 9mm, and .40 are gone. 7.62x39, 5.56 and 223 are gone. 308 and 30-30 are also sold out. Only rare shotshells are Buck shot......otherwise all calibers are readily available. Price gouging really hasn'...

Sigmar

available

Search found 91 matches