Cast bullets: bore size or throat size?

Welcome to the Leverguns.Com Forum. This is a high-class place so act respectable. We discuss most anything here ... politely.

Moderators: AmBraCol, Hobie

Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.

Please post political post in the new Politics forum.
Post Reply
Walt
Senior Levergunner
Posts: 1406
Joined: Sun Jun 19, 2022 4:01 pm
Location: NM

Cast bullets: bore size or throat size?

Post by Walt »

There have been changing discussions around how large to size cast bullets for best accuracy. Years ago it was recommended to size bullets to match groove diameter. In the past two or three decades however, the consesus has been to size bullets close to the diameter of the chamber throats, preferably a fit so close that sized bullets can be pushed through throats with a small amount of resistance.

From Ken Waters' PET LOADS in his testing of the .44 Special he stated that one of his test guns was a (relatively) recent production SAA with chamber throats of .432" and groove diameter of .427". I consider Ken Waters to have been a thoughtful and careful experimenter; based upon recent thought, he did a lot of his cast bullet sizing for the Colt at .432" to match throat diameter but found that when he reduced his bullets to .427" it cut his group size in half.

Without a doubt, each gun is a law unto itself.
Twodot
Levergunner 2.0
Posts: 310
Joined: Wed Apr 06, 2011 1:34 pm
Location: Montana

Re: Cast bullets: bore size or throat size?

Post by Twodot »

that last sentence says it all
..
Rockrat
Levergunner 2.0
Posts: 490
Joined: Wed Dec 19, 2018 8:35 pm
Location: Colorado

Re: Cast bullets: bore size or throat size?

Post by Rockrat »

I had a Colt NF in 44 spcl with pretty well, the same chamber mouth and groove dimensions. .427" leaded the bore, .429" wasn't much better, .430" was a bit better, then .431" was an improvement, .432" was pretty good and .433" was the best and I stopped there.
User avatar
Scott Tschirhart
Advanced Levergunner
Posts: 4559
Joined: Fri Oct 16, 2020 2:56 pm
Location: San Antonio, Texas

Re: Cast bullets: bore size or throat size?

Post by Scott Tschirhart »

Agreed. Experimentation can lead you to combinations that don’t make sense.
samsi
Levergunner 3.0
Posts: 523
Joined: Tue Sep 11, 2007 9:55 am
Location: AZ

Re: Cast bullets: bore size or throat size?

Post by samsi »

Assuming proper relationship of bore and throat size, my take is that it's more important to be close to throat size. It's of lesser importance with bullets of longer bearing surface that seat further out of the case to where the bullet has started into the forcing cone before clearing the case entirely (reduces tipping with under throat size bullets). I believe it's likely that's the reason that Elmer got satisfactory results with his bullet sized to groove diameter or .001 over. I have no idea what the throats were on his custom guns but the S&W's likely weren't throated very tight.
Walt
Senior Levergunner
Posts: 1406
Joined: Sun Jun 19, 2022 4:01 pm
Location: NM

Re: Cast bullets: bore size or throat size?

Post by Walt »

Yeah, Elmer said that was the reason he designed the original Lyman 429421 with a full-width front band. I also suspect he was correct in his design of a square-bottomed grease groove putting more lube into the rifling due to hydraulic effect from an obturating bullet collapsing the grease groove.
Gobblerforge
Senior Levergunner
Posts: 1510
Joined: Tue Sep 04, 2007 1:02 pm
Location: Eastern Ohio, Foothills of Appalachia
Contact:

Re: Cast bullets: bore size or throat size?

Post by Gobblerforge »

Rockrat wrote: Tue Apr 04, 2023 3:03 pm I had a Colt NF in 44 spcl with pretty well, the same chamber mouth and groove dimensions. .427" leaded the bore, .429" wasn't much better, .430" was a bit better, then .431" was an improvement, .432" was pretty good and .433" was the best and I stopped there.
Do I understand that you bought 6 different molds to try this? If so that is a serious investment into finding accuracy. What do you do with the other molds you don't use?
Click Click Boom
User avatar
Tycer
Advanced Levergunner
Posts: 7718
Joined: Sun Sep 02, 2007 10:17 am
Location: Asheville, NC

Re: Cast bullets: bore size or throat size?

Post by Tycer »

Gobblerforge wrote: Wed Apr 05, 2023 5:44 am
Rockrat wrote: Tue Apr 04, 2023 3:03 pm I had a Colt NF in 44 spcl with pretty well, the same chamber mouth and groove dimensions. .427" leaded the bore, .429" wasn't much better, .430" was a bit better, then .431" was an improvement, .432" was pretty good and .433" was the best and I stopped there.
Do I understand that you bought 6 different molds to try this? If so that is a serious investment into finding accuracy. What do you do with the other molds you don't use?
I read that as sizing dies. Or he opened one up.
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
User avatar
marlinman93
Advanced Levergunner
Posts: 6639
Joined: Sun Apr 01, 2007 3:40 pm
Location: Oregon

Re: Cast bullets: bore size or throat size?

Post by marlinman93 »

.001" over groove diameter has always worked best for my rifles. Shooting throat diameter can result in swaging down bullets as they enter the bore, and that lead has to go somewhere. Where it goes is the base of the bullet, which can lead to "fins" hanging off the base created by the lands and grooves. Anything that changes the base of the bullets will affect accuracy and not for the better.
Pre WWI Marlins and Singleshot rifles!
http://members.tripod.com/~OregonArmsCollectors/
User avatar
Griff
Posting leader...
Posts: 21016
Joined: Sat Mar 31, 2007 4:56 pm
Location: OH MY GAWD they installed a STOP light!!!

Re: Cast bullets: bore size or throat size?

Post by Griff »

.001-.002" over groove diameter has always been the rule of thumb I followed. I get a bit anxious going bigger than that with pressures, etc.
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93

There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
piller
Posting leader...
Posts: 15275
Joined: Sat Sep 29, 2007 9:49 pm
Location: South of Dallas

Re: Cast bullets: bore size or throat size?

Post by piller »

I only have 1 revolver I shoot lead bullets from. A Ruger Blackhawk with 2 cylinders. .45 Colt and 45 ACP. I buy the lead bullets sized to .452 and accuracy has been good. Funny, but the 45 ACP has been accurate as anything I can shoot with the .451 jacketed bullets. I have never measured the cylinder throats or the forcing cone. Since it can get down to an inch at 25 yards when I have a rest and am taking my time, there doesn't seem to be any reason to change anything. Freehand, my groups are about 2 or 3 inches. More than 2 cups of coffee that day opens the group up.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
User avatar
Scott Tschirhart
Advanced Levergunner
Posts: 4559
Joined: Fri Oct 16, 2020 2:56 pm
Location: San Antonio, Texas

Re: Cast bullets: bore size or throat size?

Post by Scott Tschirhart »

piller wrote: Thu Apr 06, 2023 8:03 pm I only have 1 revolver I shoot lead bullets from. A Ruger Blackhawk with 2 cylinders. .45 Colt and 45 ACP. I buy the lead bullets sized to .452 and accuracy has been good. Funny, but the 45 ACP has been accurate as anything I can shoot with the .451 jacketed bullets. I have never measured the cylinder throats or the forcing cone. Since it can get down to an inch at 25 yards when I have a rest and am taking my time, there doesn't seem to be any reason to change anything. Freehand, my groups are about 2 or 3 inches. More than 2 cups of coffee that day opens the group up.
Don’t fix what ain’t broke!

I’m shooting really soft .454 bullets in my .45 Colts for my everyday loads. My 270SAA bullets are sized to .453. I generally like my throats to measure .4525. But I haven’t even measured this one because it shoots so good.

In my .44 Special I’m shooting .430s
User avatar
Rimfire McNutjob
Advanced Levergunner
Posts: 3212
Joined: Mon Sep 03, 2007 2:51 pm
Location: Sanford, FL.

Re: Cast bullets: bore size or throat size?

Post by Rimfire McNutjob »

Glad I caught this before it rolled off of the page. Just ordered my first SAA in .45 and now I'm getting a set of pin gauges in .451- to .455- to measure the chamber throats. I managed to order some commercial ammo for my first outing but the stuff is hard to find in the bullet I want. Once I have the brass, I'll order some commercial cast based on what the pin gauges say for the throats and see how they run.
... I love poetry, long walks on the beach, and poking dead things with a stick.
Walt
Senior Levergunner
Posts: 1406
Joined: Sun Jun 19, 2022 4:01 pm
Location: NM

Re: Cast bullets: bore size or throat size?

Post by Walt »

McNutJob, the commercial caster I have used for years for anything I don't cast myself is SNS Casting. Their bullets are fairly hard; their .45 Colt bullets are sized at .452 and look great. They are available in SWC, RNFP or coated. I normally buy 1000 250 gr RNFP at a time but boxes of 500 are available as well. They have 2 day shipping and their flat rate fee is $15 last I saw. The best thing is their packaging. They use carpet padding around their boxes to protect the bullets and I have never seen any dented or deformed bullets.
piller
Posting leader...
Posts: 15275
Joined: Sat Sep 29, 2007 9:49 pm
Location: South of Dallas

Re: Cast bullets: bore size or throat size?

Post by piller »

Walt, they sound good. I will look them up.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
piller
Posting leader...
Posts: 15275
Joined: Sat Sep 29, 2007 9:49 pm
Location: South of Dallas

Re: Cast bullets: bore size or throat size?

Post by piller »

They list BHN of 16-17. Sounds reasonable to me, but I freely admit to not being any sort of expert on this subject.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
User avatar
Rimfire McNutjob
Advanced Levergunner
Posts: 3212
Joined: Mon Sep 03, 2007 2:51 pm
Location: Sanford, FL.

Re: Cast bullets: bore size or throat size?

Post by Rimfire McNutjob »

Walt wrote: Sat Apr 15, 2023 4:52 pm McNutJob, the commercial caster I have used for years for anything I don't cast myself is SNS Casting.
Wow, that seems pretty cheap for a 500ct box in 45LC. I've not really read anything on the use or performance of coated bullets.
... I love poetry, long walks on the beach, and poking dead things with a stick.
User avatar
AJMD429
Posting leader...
Posts: 32800
Joined: Sun Sep 09, 2007 10:03 am
Location: Hoosierland
Contact:

Re: Cast bullets: bore size or throat size?

Post by AJMD429 »

piller wrote: Thu Apr 06, 2023 8:03 pm…Since it can get down to an inch at 25 yards when I have a rest and am taking my time, there doesn't seem to be any reason to change anything. Freehand, my groups are about 2 or 3 inches. More than 2 cups of coffee that day opens the group up.
Wow I’d not mess with perfection either…!

The 45 ACPs in my 45 Colt RedHawk are TERRIBLE but I’ve not measured anything, and I have to admit the 45 Colt so far all is factory load ‘Cowboy’ or Buffalo Bore and they both do well but the 45 ACP is so far all old bulk commercial reloads. So that’s likely part of the difference.
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.


Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
User avatar
flightsimmer
Levergunner 2.0
Posts: 201
Joined: Tue Feb 21, 2012 10:13 am
Location: Indianapolis, In.

Re: Cast bullets: bore size or throat size?

Post by flightsimmer »

I have a 4-3/4" EMF Hartford in 45 Colt caliber.
I feel like it is perfection of the breed in every way.
I don't remember the exact specifications now but the cylinder throats were much larger than the grove in the barrel.

It bothered me enough for me to try to locate a cylinder with smaller throat sizes, I was never able to but it didn't seem to matter because it shot to middle of beer-can at 25 yards with a 6 o'clock hold and dead-on at 50 yards.

So I just accepted it as it was and learned to love it.
You do not have the required permissions to view the files attached to this post.
10mm, when you care enough to send the very best.
__________________
If possible, so much as it depends on you, be at peace with all men. Rom 12:18
User avatar
Scott Tschirhart
Advanced Levergunner
Posts: 4559
Joined: Fri Oct 16, 2020 2:56 pm
Location: San Antonio, Texas

Re: Cast bullets: bore size or throat size?

Post by Scott Tschirhart »

Yes, don’t fix what ain’t broke!
Post Reply