200 grain pin bullet in 38 or 357

Welcome to the Leverguns.Com Forum. This is a high-class place so act respectable. We discuss most anything here ... politely.

Moderators: AmBraCol, Hobie

Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.

Please post political post in the new Politics forum.
Post Reply
mickbr
Levergunner 3.0
Posts: 918
Joined: Mon Jan 22, 2018 11:29 pm

200 grain pin bullet in 38 or 357

Post by mickbr »

Tom at Accurate Moulds drew this for me. Inspiration was the old 230 grain pin shooting bullet and the 200 grain super police loads. Aka a 200 grain 'seated out wad cutter'. Purpose......well doesnt pay to get too carried away with actual reasons for doing stuff :D. I wont be shooting pins so much, maybe some water jugs and an occasional critter.
http://www.accuratemolds.com/bullet_det ... 200G-D.png
User avatar
wvfarrier
Senior Levergunner
Posts: 1533
Joined: Mon Oct 28, 2013 9:27 am
Location: West (by GOD) Virginia

Re: 200 grain pin bullet in 38 or 357

Post by wvfarrier »

That would probably make a pretty efficient anti-personnel/dangerous game bullet as well.
A bondservant of our Lord, Christ Jesus
Bill in Oregon
Advanced Levergunner
Posts: 9426
Joined: Sun Jun 29, 2008 10:05 am
Location: The Land of Enchantment

Re: 200 grain pin bullet in 38 or 357

Post by Bill in Oregon »

I have always admired heavy-for-caliber bulets. Yours is a dandy.
User avatar
AJMD429
Posting leader...
Posts: 32800
Joined: Sun Sep 09, 2007 10:03 am
Location: Hoosierland
Contact:

Re: 200 grain pin bullet in 38 or 357

Post by AJMD429 »

Have you tested for spin-stability...?
Long bullets need fast twist, although flat meplats help keep them short-for-weight versus pointy ones.
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.


Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
User avatar
6pt-sika
Advanced Levergunner
Posts: 9609
Joined: Wed Dec 19, 2007 7:15 pm
Location: Virginia

Re: 200 grain pin bullet in 38 or 357

Post by 6pt-sika »

I used to have a Lyman mold that was a .358” SWC GC that was supposed to be 215 grains . I used them a bit in Marlin 1894CB 357 with the 24” barrel . They shot really well but never checked velocity . Believe it or not I also shot them in a Marlin 1894CP 16” and again did very well . Wish I remmembered the Lyman designation number but I sold that mold close to ten years ago .
Parkers , Mannlicher Schoenauer’s , 6.5mm's and my family in the Philippines !
Bullard4075
Senior Levergunner
Posts: 1260
Joined: Thu Sep 06, 2007 11:14 pm
Location: Billings, Montana

Re: 200 grain pin bullet in 38 or 357

Post by Bullard4075 »

Worth looking into. Thanks.
"Any man who covers his face and packs a gun is a legitimate target for any decent citizen"
Jeff Cooper
mickbr
Levergunner 3.0
Posts: 918
Joined: Mon Jan 22, 2018 11:29 pm

Re: 200 grain pin bullet in 38 or 357

Post by mickbr »

AJMD429 wrote: Fri Jan 01, 2021 12:25 pm Have you tested for spin-stability...?
Long bullets need fast twist, although flat meplats help keep them short-for-weight versus pointy ones.
I dont think its any longer than the Hornady 180XTP. That said I think it will definetly keyhole in a Rossi 92 at low speeds with the 1:30. twist. Uberti and Win/miroku lever actions with about 1:18 should handle it better, also the new marlins which I think are 1:16 now?
Last edited by mickbr on Fri Jan 01, 2021 7:23 pm, edited 1 time in total.
mickbr
Levergunner 3.0
Posts: 918
Joined: Mon Jan 22, 2018 11:29 pm

Re: 200 grain pin bullet in 38 or 357

Post by mickbr »

Bill in Oregon wrote: Fri Jan 01, 2021 11:52 am I have always admired heavy-for-caliber bulets. Yours is a dandy.
Thanks Bill and I will clarify I just gave him an idea of weight, meplat and loaded length. He did the measurements and drawing.
wecsoger
Senior Levergunner
Posts: 1252
Joined: Sun Jun 08, 2008 8:40 am

Re: 200 grain pin bullet in 38 or 357

Post by wecsoger »

Wadcutters are good possibilities for defensive ammo.

This one looks...interesting.

I would really like to see testing on a batch of these.

Gas checks, relatively soft lead, and either .38 or .357 loading. (probably couldn't go too soft for .357)

Hmmm...could you even load one of these in .38 - overall length?

Newton's Third Law being still valid, I have to wonder what it's like to launch of of these down range.
Bill in Oregon
Advanced Levergunner
Posts: 9426
Joined: Sun Jun 29, 2008 10:05 am
Location: The Land of Enchantment

Re: 200 grain pin bullet in 38 or 357

Post by Bill in Oregon »

Should be fine from a .38 Special, keeping in mind the British 38/200 Mark I load was a 200-grain bullet at 625 fps in a .38 Smith & Wesson case.
mickbr
Levergunner 3.0
Posts: 918
Joined: Mon Jan 22, 2018 11:29 pm

Re: 200 grain pin bullet in 38 or 357

Post by mickbr »

overall loaded length is about 1.44".
User avatar
Tycer
Advanced Levergunner
Posts: 7718
Joined: Sun Sep 02, 2007 10:17 am
Location: Asheville, NC

Re: 200 grain pin bullet in 38 or 357

Post by Tycer »

I have a Mountain Molds 205 fat meplat. Drops .360” I can probably find the specs if you want. I can send you a few to try. I have run them to 1800 fps without leading.
E286BD90-8725-48EB-AE1E-36DC67D9618C.jpeg
You do not have the required permissions to view the files attached to this post.
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
mickbr
Levergunner 3.0
Posts: 918
Joined: Mon Jan 22, 2018 11:29 pm

Re: 200 grain pin bullet in 38 or 357

Post by mickbr »

Tycer thanks., Im chasing full meplat for this one but thanks for the offer. would be interested in any load data though ,if you want to share or PM. Understand if you prefer not, for the record everything will be fired in full strength 357's.
Bill in Oregon
Advanced Levergunner
Posts: 9426
Joined: Sun Jun 29, 2008 10:05 am
Location: The Land of Enchantment

Re: 200 grain pin bullet in 38 or 357

Post by Bill in Oregon »

That's a swell bullet there, Tycer. Ready to do some heavy lifting, like Mick's.
User avatar
Tycer
Advanced Levergunner
Posts: 7718
Joined: Sun Sep 02, 2007 10:17 am
Location: Asheville, NC

Re: 200 grain pin bullet in 38 or 357

Post by Tycer »

mickbr wrote: Mon Jan 04, 2021 8:44 am Tycer thanks., Im chasing full meplat for this one but thanks for the offer. would be interested in any load data though ,if you want to share or PM. Understand if you prefer not, for the record everything will be fired in full strength 357's.
I really can't because that bullet was designed for my Win 94 360 Dan Wesson. I've never loaded it in a 357 case.
I will say that Lil'Gun was my best powder and it seems to perform best at ~90% available case volume below the bullet. 360 DW, 357 Mag and 32-20.
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
User avatar
Tycer
Advanced Levergunner
Posts: 7718
Joined: Sun Sep 02, 2007 10:17 am
Location: Asheville, NC

Re: 200 grain pin bullet in 38 or 357

Post by Tycer »

Bill in Oregon wrote: Mon Jan 04, 2021 10:14 am That's a swell bullet there, Tycer. Ready to do some heavy lifting, like Mick's.
I gotta tell ya. A heavy, large meplat 357 cal bullet will poke a clean 3/4" hole through and through. I mean it looks like a piece of copper tubing was driven through. No bloodshot meat-eat right up to the hole. At 1850 fps mv that bullet has traveled through 40" of meat and bone and kept on going.
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
reivertom
Levergunner
Posts: 24
Joined: Wed Mar 25, 2020 11:19 pm

Re: 200 grain pin bullet in 38 or 357

Post by reivertom »

That's a "Me-splat"
Bill in Oregon
Advanced Levergunner
Posts: 9426
Joined: Sun Jun 29, 2008 10:05 am
Location: The Land of Enchantment

Re: 200 grain pin bullet in 38 or 357

Post by Bill in Oregon »

Tycer, that bullet alone has me daydreaming about a little 92 in .357 for the first time in many, many years.
mickbr
Levergunner 3.0
Posts: 918
Joined: Mon Jan 22, 2018 11:29 pm

Re: 200 grain pin bullet in 38 or 357

Post by mickbr »

Tycer wrote: Tue Jan 05, 2021 12:43 pm
I really can't because that bullet was designed for my Win 94 360 Dan Wesson. I've never loaded it in a 357 case.
I will say that Lil'Gun was my best powder and it seems to perform best at ~90% available case volume below the bullet. 360 DW, 357 Mag and 32-20.
Thanks Tycer, no probs. I found some data out there for the 200 grain super police type bullets. Should be fun for starters
Dave James
Levergunner 2.0
Posts: 238
Joined: Sat Sep 08, 2007 2:47 pm
Location: Tidewater VA

Re: 200 grain pin bullet in 38 or 357

Post by Dave James »

The old "Highway" load with the 200 grain round nose, was great punching cars at the time but little else unless it hit bone, it just whizzed through, the body, I know from experience, solid wad cutters seemed to work better {I believe} because of the lip on the face, and the lead being softer
piller
Posting leader...
Posts: 15275
Joined: Sat Sep 29, 2007 9:49 pm
Location: South of Dallas

Re: 200 grain pin bullet in 38 or 357

Post by piller »

I like the flat wide nose bullets for the hunting I have done with them. Success without a lot of torn up meat is pretty hard to argue with.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
Marvin S
Levergunner 3.0
Posts: 832
Joined: Wed Jul 21, 2010 9:55 pm
Location: Kansas

Re: 200 grain pin bullet in 38 or 357

Post by Marvin S »

Here’s a full box.
You do not have the required permissions to view the files attached to this post.
Post Reply