1892 Winchester tang bolts
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
- fordwannabe
- Advanced Levergunner
- Posts: 3370
- Joined: Thu Apr 02, 2009 8:52 am
- Location: Womelsdorf PA
1892 Winchester tang bolts
Oh enlighten ones a buddy of mine has a 1892 circa 1897. When he purchased it it had a screw of sort sort that was NOT Winchester and a square nut as a tang screw. He bought a screw from gunparts Corp supposedly fits 1892 and 1894. Nope won’t fit in the threads. Any idea if the 92 and the 94 should use the same tang screw? Thanks
a Pennsylvanian who has been accused of clinging to my religion and my guns......Good assessment skills.
Re: 1892 Winchester tang bolts
.
AFAIK, the tang screws are not identical, but if you message fellow forum member Steve ( www.stevesgunz.com ) he can tell you for sure.
OTOH, did the tang screw threads in the lower tang get messed up when the stovebolt was installed ?
If so, you might be able to just chase the threads & use the tang screw you ordered.
.
AFAIK, the tang screws are not identical, but if you message fellow forum member Steve ( www.stevesgunz.com ) he can tell you for sure.
OTOH, did the tang screw threads in the lower tang get messed up when the stovebolt was installed ?
If so, you might be able to just chase the threads & use the tang screw you ordered.
.
- earlmck
- Advanced Levergunner
- Posts: 3447
- Joined: Tue Nov 30, 2010 12:10 am
- Location: pert-neer middle of Oregon
Re: 1892 Winchester tang bolts
Should use the same screw. 12-28 by about 1.8 or so.
The greatest patriot...
is he who heals the most gullies. Patrick Henry
is he who heals the most gullies. Patrick Henry
- fordwannabe
- Advanced Levergunner
- Posts: 3370
- Joined: Thu Apr 02, 2009 8:52 am
- Location: Womelsdorf PA
Re: 1892 Winchester tang bolts
Thanks guys. He is gonna bring it over this week and we are gonna try a couple out of my guns. With your responses now I wonder what’s up?
a Pennsylvanian who has been accused of clinging to my religion and my guns......Good assessment skills.
- Sixgun
- Posting leader...
- Posts: 18733
- Joined: Sun Sep 16, 2007 7:17 pm
- Location: S.E. Pa. Where The Finest Winchesters & Colts Reside
Re: 1892 Winchester tang bolts
Earl hit it right Tommy......I keep a couple of dozen laying around....even have a tap and die......if the threads are buggered up most hardware stores carry that size. ----6
- GunnyMack
- Advanced Levergunner
- Posts: 10214
- Joined: Mon Sep 19, 2016 7:57 am
- Location: Not where I want to be!
Re: 1892 Winchester tang bolts
Most gun screws are bastard sizes. 6-48, 1/4-22(Mauser guard screws), 12-28, yer not going to find these at local hardware stores.
In this situation I'm wondering if the threads were drilled out to allow the nut & bolt to be used...? Yes it's a good idea to keep old/odd screws on hand. Numrich is your friend!
In this situation I'm wondering if the threads were drilled out to allow the nut & bolt to be used...? Yes it's a good idea to keep old/odd screws on hand. Numrich is your friend!
BROWN LABS MATTER !!
- fordwannabe
- Advanced Levergunner
- Posts: 3370
- Joined: Thu Apr 02, 2009 8:52 am
- Location: Womelsdorf PA
Re: 1892 Winchester tang bolts
In this case the hole in the tang is smaller than the screw they sent. It looks like the screw is approximately.020 bigger than the hole.
a Pennsylvanian who has been accused of clinging to my religion and my guns......Good assessment skills.
- GunnyMack
- Advanced Levergunner
- Posts: 10214
- Joined: Mon Sep 19, 2016 7:57 am
- Location: Not where I want to be!
Re: 1892 Winchester tang bolts
Hey FW, does the screw fit from the top but the threads do not?
According to a tap/ drill chart a 12-28 should have a hole of .1812 or a #14 drill for optimum threading.
According to a tap/ drill chart a 12-28 should have a hole of .1812 or a #14 drill for optimum threading.
BROWN LABS MATTER !!
- Sixgun
- Posting leader...
- Posts: 18733
- Joined: Sun Sep 16, 2007 7:17 pm
- Location: S.E. Pa. Where The Finest Winchesters & Colts Reside
Re: 1892 Winchester tang bolts
Another thing is to try screwing it in from underneath....sometimes people only bugger the threads up half to 3/4 way down.
-
- Advanced Levergunner
- Posts: 4296
- Joined: Wed Sep 15, 2010 12:57 pm
- Location: Vinita, I.T.
Re: 1892 Winchester tang bolts
12-28 IS a standard size and quite common. Taps and dies are generally available at your local ACE hardware or similar. I've seen them at Lowes. Most gun screws are from the extra fine series and only common in guns and instruments.
M. M. Wright, Sheriff, Green county Arkansas (1860)
Currently living my eternal life.
NRA Life
SASS
ITSASS
Currently living my eternal life.
NRA Life
SASS
ITSASS
- fordwannabe
- Advanced Levergunner
- Posts: 3370
- Joined: Thu Apr 02, 2009 8:52 am
- Location: Womelsdorf PA
Re: 1892 Winchester tang bolts
Doesn’t fit too or bottom.
a Pennsylvanian who has been accused of clinging to my religion and my guns......Good assessment skills.
- Sixgun
- Posting leader...
- Posts: 18733
- Joined: Sun Sep 16, 2007 7:17 pm
- Location: S.E. Pa. Where The Finest Winchesters & Colts Reside
Re: 1892 Winchester tang bolts
Tom..it comes down to this...get a 12-28 tap....and a die ...you will need it again in the future........and run it through...if it looks like there's enough meat to grab the screw, your in business. If not, your going to have to go up to a preferable 1/4 x 28 and probably will have to make the screw. The common 1/4 x 20 will be too coarse..it will work but eehhh, I don't like coarse screws on guns except for the wood.
Worst comes to worse, spend $50 on gas and stop over...I have all the stuff to make you a screw. Bring a stack of Ben's with ya....maybe something you want to go home with. ---6
Worst comes to worse, spend $50 on gas and stop over...I have all the stuff to make you a screw. Bring a stack of Ben's with ya....maybe something you want to go home with. ---6
- earlmck
- Advanced Levergunner
- Posts: 3447
- Joined: Tue Nov 30, 2010 12:10 am
- Location: pert-neer middle of Oregon
Re: 1892 Winchester tang bolts
Sounds to me like they sent you the wrong screw. My local NAPA store has been real good about telling me what I have when I bring in a mystery screw. You might give yours a try with both the old screw and the replacement to see what you are working with.
Ford, why not pull a tang screw out of one of your rifles and see if it fits your buddy's?
Ford, why not pull a tang screw out of one of your rifles and see if it fits your buddy's?
The greatest patriot...
is he who heals the most gullies. Patrick Henry
is he who heals the most gullies. Patrick Henry
- GunnyMack
- Advanced Levergunner
- Posts: 10214
- Joined: Mon Sep 19, 2016 7:57 am
- Location: Not where I want to be!
Re: 1892 Winchester tang bolts
I too think you have the wrong screw.
Every gun guy should spend the money for a thread pitch gauge. This will not do metric but they are available.
Just try different pitches until you find the right one.
Every gun guy should spend the money for a thread pitch gauge. This will not do metric but they are available.
Just try different pitches until you find the right one.
You do not have the required permissions to view the files attached to this post.
BROWN LABS MATTER !!