holes. When did Marlin start drilling and tapping the top of the receivers?
not that it matters. I'm most likely going to buy it anyway. More curiosity than anything else.
jb
When did Marlin start D&T'ing top of receivers for mounts?
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
-
2ndovc
- Advanced Levergunner
- Posts: 9624
- Joined: Fri Sep 07, 2007 11:59 am
- Location: OH, South Shore of Lake Erie
When did Marlin start D&T'ing top of receivers for mounts?
Looking at a Marlin 336 RC that dates to 1957/8. The owner says they are factory
holes. When did Marlin start drilling and tapping the top of the receivers?
not that it matters. I'm most likely going to buy it anyway. More curiosity than anything else.
jb
holes. When did Marlin start drilling and tapping the top of the receivers?
not that it matters. I'm most likely going to buy it anyway. More curiosity than anything else.
jb
jasonB " Another Dirty Yankee"
" Tomorrow the sun will rise. Who knows what the tide could bring?"
" Tomorrow the sun will rise. Who knows what the tide could bring?"
Re: When did Marlin start D&T'ing top of receivers for mounts?
1957 for the 39A & 336, though Brophy's book says 1956 I have never seen one. It started with the introduction of the Golden 39A.
I know a whole lot about very little and nothing about a whole lot.
-
buckeyeshooter
- Senior Levergunner
- Posts: 1263
- Joined: Mon Dec 17, 2007 7:57 pm
Re: When did Marlin start D&T'ing top of receivers for mounts?
If I remember correctly it was the mid 50's.
-
2ndovc
- Advanced Levergunner
- Posts: 9624
- Joined: Fri Sep 07, 2007 11:59 am
- Location: OH, South Shore of Lake Erie
Re: When did Marlin start D&T'ing top of receivers for mounts?
Thanks. That would fit.
I haven't had it in my hands yet and the photos aren't great. But the price is right and I want a .35 Rem.
jb
I haven't had it in my hands yet and the photos aren't great. But the price is right and I want a .35 Rem.
jb
jasonB " Another Dirty Yankee"
" Tomorrow the sun will rise. Who knows what the tide could bring?"
" Tomorrow the sun will rise. Who knows what the tide could bring?"
Re: When did Marlin start D&T'ing top of receivers for mounts?
I have owned a very nice 1949-vintage 39A for several years. It came with a scope mount, and I knew it was not factory-original. But the scope base is an old Marlin base, and that plus the quality of the D&T job make me strongly suspect it was returned to the factory for the modification early on.
A scope does take away from the eye appeal of the 39A's lines, but I'll confess my pushing-60 eyes appreciate the assistance of the glass. The best thing about it -- I bought it for about $200 less than a comparable non-D&T'd specimen would have cost me.
A scope does take away from the eye appeal of the 39A's lines, but I'll confess my pushing-60 eyes appreciate the assistance of the glass. The best thing about it -- I bought it for about $200 less than a comparable non-D&T'd specimen would have cost me.
Re: When did Marlin start D&T'ing top of receivers for mounts?
Some 336 rifles were factory drilled and tapped as early as 1955.