Nitriding gun parts other than barrels, frames, & slides?

Welcome to the Leverguns.Com Forum. This is a high-class place so act respectable. We discuss most anything here ... politely.

Moderators: AmBraCol, Hobie

Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.

Please post political post in the new Politics forum.
Post Reply
Naphtali
Levergunner 2.0
Posts: 441
Joined: Sun Apr 27, 2008 2:21 pm
Location: Montana

Nitriding gun parts other than barrels, frames, & slides?

Post by Naphtali »

I have several Winchester and Winchester reproduction traditional lever action rifles, some of which are stainless steel. Functionally, I find them smoother and easier to operate than my [JM] Marlin 1895s that have been improved in fit and function by a Marlin specialist gunsmith. The Winchesters are also a pain to clean - with or without my MCTD autoimmune illness - again, compared with my Marlin 1895s.

I notice that handgun manufacturers and some manufacturers of semiautomatic legal clones of military automatic rifles furnish guns with nitrided parts. Usually these parts are major ones, such as barrels, frames, and slides. I have also read a very small number of posters on gun-oriented forums mention having their rifle barrels nitrided. These posters appear to be satisfied with quality of the after-market work done, and also its functionality.

1. Can smaller action parts of my lever action rifles be safely and reliably nitrided? When nitrided, will action parts warp or distort or become too brittle or some other serious long-term problem?

2. Can I specify surface color of nitrided parts among black/charcoal gray, sliver, gold, other? If I can, do properties of nitride in/on a part change significantly?

3. As best you can, please recommend after-market nitriding businesses with whom you or good acquaintances have done business.
It's so simple to be wise. Just think of something stupid to say and then don't say it. Sam Levinson
User avatar
GunnyMack
Advanced Levergunner
Posts: 9939
Joined: Mon Sep 19, 2016 7:57 am
Location: Not where I want to be!

Re: Nitriding gun parts other than barrels, frames, & slides?

Post by GunnyMack »

Your concerns are valid. However I cant answer your questions. I would suggest you speak with the company that do nitriding and get the expert professional answers you are looking for.
BROWN LABS MATTER !!
piller
Posting leader...
Posts: 15188
Joined: Sat Sep 29, 2007 9:49 pm
Location: South of Dallas

Re: Nitriding gun parts other than barrels, frames, & slides?

Post by piller »

Sounds like a good answer to me.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
hayabusa
Levergunner 2.0
Posts: 434
Joined: Sun Feb 07, 2010 5:42 pm

Re: Nitriding gun parts other than barrels, frames, & slides?

Post by hayabusa »

My thoughts also.
User avatar
Ray
Advanced Levergunner
Posts: 2823
Joined: Thu Sep 20, 2007 2:45 am

Re: Nitriding gun parts other than barrels, frames, & slides?

Post by Ray »

blacknitride.com
m.A.g.a. !
Pete44ru
Advanced Levergunner
Posts: 11242
Joined: Sun Sep 02, 2007 7:26 am

Re: Nitriding gun parts other than barrels, frames, & slides?

Post by Pete44ru »

Naphtali wrote: Sat Oct 13, 2018 2:51 pm
The Winchesters are also a pain to clean - with or without my MCTD autoimmune illness - again, compared with my Marlin 1895s.

I'm sorry that I can't answer your nitrading question, but cab tell you, having experience with both, that the Winchester 94's are only marginally harder to clean than a Marlin.

With a Winchester, just remove the large-headed finger lever stop screw from the LH side of the receiver, open the bolt about 1/2" and push out the bolt/lever pin from the opposite side - then drop the lever & locking bolt out of the way and remove the bolt to the rear. (reassemble in reverse order ;) )


.
Post Reply