Friend George called the other night, said he'd been to a gun show in Pendleton and had acquired a Savage 1899 in 32/40. He'd found one box of shells at the gunshow but they wanted $80 for them and he thought that sounded awful steep.
I assured him we could do better, so ordered up some 32/40 dies (of the Lee persuasion). They arrived yesterday, so I had to see how they'd do reworking some WW 32 Special cases. Also tried some R-P 30/30's. Here's the result:
The two loaded rounds in the center are made from 30/30 cases while the outside loaded rounds are from 32 Special. Empty 32 Special cases were the parent material, so to speak.
The Lee neck expander is such a nice gradual taper that making the cases from 30/30's seemed to add no extra effort and they turned out fully as nicely formed as those from the 32 Special cases, other than it took me a few tries to get the lube cut down to where I didn't get wrinkles. Also found I needed to go in several stages, easing the case in a half inch or so, then backing out and re-smearing lube around. I did note with a bit of disappointment that these Lee dies are not really well polished, especially in the neck area (I think you can tell that from the picture). But when old George shows up here next time (he lives some distance away, over toward the Idaho border) we should have some shootin' ammo to allow us to try out his new baby.
I used 20.5 grains if IMR 4198 with the 170 flat nose and the 165 grain FTX bullets. Old Lyman manual suggestion...
Smilin' Mack's 32/40 factory
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
- earlmck
- Advanced Levergunner
- Posts: 3450
- Joined: Tue Nov 30, 2010 12:10 am
- Location: pert-neer middle of Oregon
Smilin' Mack's 32/40 factory
You do not have the required permissions to view the files attached to this post.
The greatest patriot...
is he who heals the most gullies. Patrick Henry
is he who heals the most gullies. Patrick Henry
- AJMD429
- Posting leader...
- Posts: 32294
- Joined: Sun Sep 09, 2007 10:03 am
- Location: Hoosierland
- Contact:
Re: Smilin' Mack's 32/40 factory
I just LOVE projects like that. Sounds fun...!
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
- ollogger
- Advanced Levergunner
- Posts: 2808
- Joined: Mon Jul 05, 2010 2:47 pm
- Location: Wheatland Wyoming
- Contact:
Re: Smilin' Mack's 32/40 factory
nice job Earl! I know id be anxious in shooting that old 99
ollogger
ollogger
-
- Advanced Levergunner
- Posts: 2569
- Joined: Sat Sep 15, 2007 12:51 pm
Re: Smilin' Mack's 32/40 factory
Aint hand loading a kick !
![Cool 8)](./images/smilies/icon_cool.gif)
![Cool 8)](./images/smilies/icon_cool.gif)
![Cool 8)](./images/smilies/icon_cool.gif)
"IT IS MY OPINION, AND I AM CORRECT SO DON'T ARGUE, THE 99 SAVAGE IS THE FINEST RIFLE EVER MADE IN AMERICA."
WIL TERRY
WIL TERRY
- Sixgun
- Posting leader...
- Posts: 18783
- Joined: Sun Sep 16, 2007 7:17 pm
- Location: S.E. Pa. Where The Finest Winchesters & Colts Reside
Re: Smilin' Mack's 32/40 factory
Earl,
That's all I have been doing to make ammo for the 32-40 for many years.......run a 30-30 case in a 32-40 FLS. They do come up a bit short but I just seat the bullet where it should be for max OAL and use a Lee FCD that Lee made for me.
I have done a fair amount of testing the short brass vs. long brass and never could find a difference in accuracy. I use the RCBS bullet with a gas check and 18-20 grains of 5744.
With 6.5 grains of Unique the velocity is right around 1000 and will poke beer cans out to 200 meters------6
That's all I have been doing to make ammo for the 32-40 for many years.......run a 30-30 case in a 32-40 FLS. They do come up a bit short but I just seat the bullet where it should be for max OAL and use a Lee FCD that Lee made for me.
I have done a fair amount of testing the short brass vs. long brass and never could find a difference in accuracy. I use the RCBS bullet with a gas check and 18-20 grains of 5744.
With 6.5 grains of Unique the velocity is right around 1000 and will poke beer cans out to 200 meters------6
- gamekeeper
- Spambot Zapper
- Posts: 17487
- Joined: Thu Sep 06, 2007 3:32 pm
- Location: Over the pond unfortunately.
Re: Smilin' Mack's 32/40 factory
Please let us know how they perform in that old 1899..... ![Cool 8)](./images/smilies/icon_cool.gif)
![Cool 8)](./images/smilies/icon_cool.gif)
Whatever you do always give 100%........... unless you are donating blood.
-
- Senior Levergunner
- Posts: 1026
- Joined: Thu Sep 06, 2007 5:57 pm
- Location: Central Maine
Re: Smilin' Mack's 32/40 factory
How about some picks of the old girl?
Mainehunter :![Wink :wink:](./images/smilies/icon_wink.gif)
Mainehunter :
![Wink :wink:](./images/smilies/icon_wink.gif)
- earlmck
- Advanced Levergunner
- Posts: 3450
- Joined: Tue Nov 30, 2010 12:10 am
- Location: pert-neer middle of Oregon
Re: Smilin' Mack's 32/40 factory
Turns out that my 30/30 FC die will crimp these slightly short (about .1") 32/40 cases if needed. I'll have to wait for George and his gun to show up so we can try these for final fit before putting in much of a crimp. And if he gets disgusted with his rifle and runs off and leaves it behind I might invest in a .32 mold. Meanwhile we'll muddle along with some jacketed bullets I bought for the 32 Special with the pitted bore that is going to get rebored into something "one of these days".Sixgun wrote:Earl,
That's all I have been doing to make ammo for the 32-40 for many years.......run a 30-30 case in a 32-40 FLS. They do come up a bit short but I just seat the bullet where it should be for max OAL and use a Lee FCD that Lee made for me.
I have done a fair amount of testing the short brass vs. long brass and never could find a difference in accuracy. I use the RCBS bullet with a gas check and 18-20 grains of 5744.
With 6.5 grains of Unique the velocity is right around 1000 and will poke beer cans out to 200 meters------6
I'll try for some pics when the rifle and its owner show up for a visit. Meanwhile, we are ready here.Mainehunter wrote:How about some picks of the old girl?
The greatest patriot...
is he who heals the most gullies. Patrick Henry
is he who heals the most gullies. Patrick Henry