winchester info. needed
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
- plowboy 45
- Senior Levergunner
- Posts: 1370
- Joined: Thu Dec 26, 2013 9:42 pm
- Location: PURVIS, MISSISSIPPI
winchester info. needed
What's the value of a 1886 in 38 56, nice wood normal wear nice patina, octagon barrel?
Re: winchester info. needed
Any pic's? $2500-$4000. Condition means a lot.
Byron
Byron
- plowboy 45
- Senior Levergunner
- Posts: 1370
- Joined: Thu Dec 26, 2013 9:42 pm
- Location: PURVIS, MISSISSIPPI
Re: winchester info. needed
Yea but there on my phone its got a little rust on barrel. Tell me about the cartridge, can it be had or replaced, with another.
- plowboy 45
- Senior Levergunner
- Posts: 1370
- Joined: Thu Dec 26, 2013 9:42 pm
- Location: PURVIS, MISSISSIPPI
Re: winchester info. needed
It looks like most old guns do to me. Used, normal for its age.
-
- Advanced Levergunner
- Posts: 4296
- Joined: Wed Sep 15, 2010 12:57 pm
- Location: Vinita, I.T.
Re: winchester info. needed
Condition is everything when guessing value. Pics??? Sure, it could be rebored to about whatever you want but I'll bet you can find the stuff to load for 38-56.
M. M. Wright, Sheriff, Green county Arkansas (1860)
Currently living my eternal life.
NRA Life
SASS
ITSASS
Currently living my eternal life.
NRA Life
SASS
ITSASS
Re: winchester info. needed
Just neck down 45/70. Lee makes dies. 38/55 bullets.
Byron
Byron
Re: winchester info. needed
Yep, make brass from 45/70. 38- 56 headstamped brass is hard to find and pricey. I think Buffalo arms sells ammo for it both ways, but it ain't cheap.
- plowboy 45
- Senior Levergunner
- Posts: 1370
- Joined: Thu Dec 26, 2013 9:42 pm
- Location: PURVIS, MISSISSIPPI
Re: winchester info. needed
Thanks for the info I went ahead and bought it I'll post pics when it gets here.thanks again
-
- Levergunner 2.0
- Posts: 369
- Joined: Wed Mar 12, 2014 6:41 pm
Re: winchester info. needed
I had one. 38-56 groove diameters can vary. Mine was .384".
Re: winchester info. needed
Glad you got it. I have some resized brass for it if you end up wanting it. It is actually loaded ammo, but I do not know what the load is so if you want it I will pull it down and ship the components.
- plowboy 45
- Senior Levergunner
- Posts: 1370
- Joined: Thu Dec 26, 2013 9:42 pm
- Location: PURVIS, MISSISSIPPI
Re: winchester info. needed
Thanks for the info and comment s it will be here monday. I'll get back with y'all on the brass and other when I check out the gun. Didn't think I could go wrong at $700. Cost me an extra $94 to get it here that quick.
- plowboy 45
- Senior Levergunner
- Posts: 1370
- Joined: Thu Dec 26, 2013 9:42 pm
- Location: PURVIS, MISSISSIPPI
Re: winchester info. needed
Thanks earl, good info.