Rifling twist rate in a Mossin Nagant?
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Rifling twist rate in a Mossin Nagant?
Maybe someone here knows what the old Mossin Nagant rifles have for rifling twist
rate?
rate?
What in the wild world of sports is going on here
- O.S.O.K.
- Advanced Levergunner
- Posts: 5533
- Joined: Sun Apr 27, 2008 4:15 pm
- Location: Deep in the Piney Woods of Mississippi
Re: Rifling twist rate in a Mossin Nagant?
IIRC, they are the metric equivalent of 1:10"
ETA: yes, I checked - is 1:9.45"
ETA: yes, I checked - is 1:9.45"
NRA Endowment Life
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
Re: Rifling twist rate in a Mossin Nagant?
Thank you! I thought I might keep bullets on the heavy side and keep the speed down.
I would like to go upwards of 200gr at around 2300-2500 fps.Maybe even a round nose.
I would like to go upwards of 200gr at around 2300-2500 fps.Maybe even a round nose.
What in the wild world of sports is going on here
- 2ndovc
- Advanced Levergunner
- Posts: 9357
- Joined: Fri Sep 07, 2007 11:59 am
- Location: OH, South Shore of Lake Erie
Re: Rifling twist rate in a Mossin Nagant?
The Hornady .312/ 174 gr RN has been a great bullet for my Moisin's and 1895 Winchester Muskets.
jb
jb
jasonB " Another Dirty Yankee"
" Tomorrow the sun will rise. Who knows what the tide could bring?"
" Tomorrow the sun will rise. Who knows what the tide could bring?"
Re: Rifling twist rate in a Mossin Nagant?
Moisin's have rifling? :>)
I can't fnd reloading brass. Everybody claims it's cheaper to use milsurp, but I know I could produce better ammo.
I can't fnd reloading brass. Everybody claims it's cheaper to use milsurp, but I know I could produce better ammo.
- O.S.O.K.
- Advanced Levergunner
- Posts: 5533
- Joined: Sun Apr 27, 2008 4:15 pm
- Location: Deep in the Piney Woods of Mississippi
Re: Rifling twist rate in a Mossin Nagant?
I highly recommend loading gas check 200 grain .314" cast bullets (Lyman mold) to around 1850 fps or so - they are accurate, shoot a bit lowwer too - allowing you to adjust the sights to near point of impact at 100 yards
NRA Endowment Life
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
-
- Levergunner 3.0
- Posts: 995
- Joined: Mon Feb 04, 2008 10:29 pm
- Location: Idaho panhandle/Wyoming
Re: Rifling twist rate in a Mossin Nagant?
2571: I have lots of mil surp ammo, some of it is brass cased. I take twenty rounds and pull the bullets with an inertia puller, weigh each charge of powder, average them, use a bullet of the same weight or a little lighter (hunting type soft nose) and reload useing a set of dies with the deprimer pin removed to neck size.. clean your gun just the same (still corrosive). That should give you a project for a rainy day... Les
This is plagiarized from someone else, but I love it!
I was born a gun owner.
It wasn't a choice.
I didn't become one later in life.
I was born this way.
I was born a gun owner.
It wasn't a choice.
I didn't become one later in life.
I was born this way.
Re: Rifling twist rate in a Mossin Nagant?
Graf & Sons lists 7.62x54R Prvi Partizan unprimed brass for under $50/100 but I see that they are currently out of stock. Opinions vary on the quality of Prvi brass but I have had good luck with their 7x57 and 303 British.2571 wrote:Moisin's have rifling? :>)
I can't fnd reloading brass. Everybody claims it's cheaper to use milsurp, but I know I could produce better ammo.
Re: Rifling twist rate in a Mossin Nagant?
I found some 174gr steel case mil cheapies for 12$. If I can keep them in a 5" circle
at 200 yards with irons I will be happy with that.This is the third mossin I played with.Its
going to get a Boyds stock,slick up the bolt,trigger clean up, and I do a nice bent bolt that
looks factory to the untrained eye.A cheap project that ends up fairly nice and allows me
to shoot more without wearing out all the good guns in my small collection.
at 200 yards with irons I will be happy with that.This is the third mossin I played with.Its
going to get a Boyds stock,slick up the bolt,trigger clean up, and I do a nice bent bolt that
looks factory to the untrained eye.A cheap project that ends up fairly nice and allows me
to shoot more without wearing out all the good guns in my small collection.
What in the wild world of sports is going on here
Re: Rifling twist rate in a Mossin Nagant?
"I do a nice bent bolt that looks factory to the untrained eye"
Do you have a photo? It would be interesting to see your work.
Do you have a photo? It would be interesting to see your work.
Re: Rifling twist rate in a Mossin Nagant?
I am sorry that this was not meant for me, but just a thought about Mosin-Nagant bolts, get a sniper bent bolt and do the modification from that. It will save a ton of work.Hawkeye2 wrote:"I do a nice bent bolt that looks factory to the untrained eye"
Do you have a photo? It would be interesting to see your work.
Steve
Re: Rifling twist rate in a Mossin Nagant?
When I get this one done in a few weeks I'll see about some photos.I don't go crazy
with the bend.A nice 45 degrees and I might try to lengthen and enlarge the knob.I make
wafer thin cuts where I want the bend,then remove material on the inside of the bend,next
I wrap the bolt in a wet rag.The next step is to weld the grove up one spot weld at a time
sometimes waiting a minute or two between spots.I don't let the bolt get hot!Once I have
the material built up how I want it I rough out the shape with the dremmel then finish up
shaping with emery cloth.Once shaped alittle fine emery cloth and a wire wheel to finish.
with the bend.A nice 45 degrees and I might try to lengthen and enlarge the knob.I make
wafer thin cuts where I want the bend,then remove material on the inside of the bend,next
I wrap the bolt in a wet rag.The next step is to weld the grove up one spot weld at a time
sometimes waiting a minute or two between spots.I don't let the bolt get hot!Once I have
the material built up how I want it I rough out the shape with the dremmel then finish up
shaping with emery cloth.Once shaped alittle fine emery cloth and a wire wheel to finish.
What in the wild world of sports is going on here