Cast bullets in 45/70 problem
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
- rock-steady
- Levergunner 2.0
- Posts: 442
- Joined: Tue Dec 18, 2007 7:35 am
- Location: Deplorable Red State
Cast bullets in 45/70 problem
I loaded ten rounds of 45/70 using the LEE 405gr cast with wheelweight alloy and 15grains of Unique. I fired five rounds from my Marlin 1895 and my nephew fired five rounds in his Handi-Rifle. At 50 yards, all five of my rounds hit the 18" x 18" paper target. All were key holing. My nephew's five rounds grouped under 1 1/2" dead center of point of aim. No signs of key holing and he said the cast rounds grouped better than the Leverlution rounds he hiunts with. My question is why did identically loaded rounds key hole in the Marlin and shoot great out of the Handi?
"People who need long explanations at moments when everything depends on instinct have always irritated me." ~ Guy Sajer
- Borregos
- Advanced Levergunner
- Posts: 4756
- Joined: Thu Sep 13, 2007 7:40 am
- Location: Ontario, Canada
Re: Cast bullets in 45/70 problem
Different bore sizes, you need to slug the Marlin bore and size the cast bullets approximately .001" larger.
Pete
Sometimes I wonder if it is worthwhile gnawing through the leather straps to get up in the morning..................
Sometimes I wonder if it is worthwhile gnawing through the leather straps to get up in the morning..................
- kimwcook
- Advanced Levergunner
- Posts: 7978
- Joined: Tue Sep 04, 2007 10:01 pm
- Location: Soap Lake, WA., U.S.A.
Re: Cast bullets in 45/70 problem
Borregos is probably on to your problem. If the bullets too small you should be mining lead out of your bore. Slugging it will give you a good starting point.
Old Law Dawg
- Old Ranger
- Levergunner 2.0
- Posts: 201
- Joined: Wed Oct 20, 2010 1:44 pm
- Location: East Texas
Re: Cast bullets in 45/70 problem
I had a similar problem with my GG when I got it a few years ago. I had used for the past 45 years, an Ideal (now Lyman) 457124, a 385 gr in Lyman #2, or a 405 in a soft mix of 1:30. With my old original Trapdoors and my Sharps, this bullet was my workhorse slug for years. Flash forward to 2009 and the Marlin GG. It would not shoot this bullet no matter what load, diameter sized (and yes, I did slug the bore at .4565") lube changes and everything. It would keyhole like crazy with this bullet. I switched to the Lee 405 Hollow Base and problem solved. Same with the Lee 340 RNFP. Never a keyhole again. In my weapon, I found that it perfers a shorter and lighter bullet. Even 300 gr RNFP's shoot great but a longer bullet....forget it! KEYHOLE!! Could just be as simple as changing the bullet you use to stop the keyhole problem...Shuck, 20 bucks will get you another mould to use and it will at least not cost much to see how a different bullet performs..
Good luck either way,
Wade
Good luck either way,
Wade
Aim low boys! They're riddin' shetlands!
- O.S.O.K.
- Advanced Levergunner
- Posts: 5533
- Joined: Sun Apr 27, 2008 4:15 pm
- Location: Deep in the Piney Woods of Mississippi
Re: Cast bullets in 45/70 problem
Yep. A bit undersized for your Marlin's bore.
If you are using a Lee sizing kit, consider that you can chuck a bronze brush into a hand drill and wrap a cleaning patch around it - then apply some lapping compound - and run this through the sizing die to open it .001-.002".
You will want it about .459-.460". A wee bit oversized cast boolits are entirely safe to shoot and will give better accuracy.
If you are using a Lee sizing kit, consider that you can chuck a bronze brush into a hand drill and wrap a cleaning patch around it - then apply some lapping compound - and run this through the sizing die to open it .001-.002".
You will want it about .459-.460". A wee bit oversized cast boolits are entirely safe to shoot and will give better accuracy.
NRA Endowment Life
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
-
- Levergunner 2.0
- Posts: 482
- Joined: Fri Sep 21, 2007 11:25 am
- Location: NE Ohio
Re: Cast bullets in 45/70 problem
Does your Marlin have microgroove rifling???
"...for there is a cloud on my horizon...and its name is progress." E. Abbey, 1958
- rock-steady
- Levergunner 2.0
- Posts: 442
- Joined: Tue Dec 18, 2007 7:35 am
- Location: Deplorable Red State
Re: Cast bullets in 45/70 problem
[quote][Does your Marlin have microgroove rifling???
/quote]
I'm embarrassed to say, I don't know. I will look when I get home. I do know it is an older model with smooth wood and it has the cross-bolt safety.
/quote]
I'm embarrassed to say, I don't know. I will look when I get home. I do know it is an older model with smooth wood and it has the cross-bolt safety.
"People who need long explanations at moments when everything depends on instinct have always irritated me." ~ Guy Sajer
-
- Advanced Levergunner
- Posts: 6747
- Joined: Thu Mar 19, 2009 9:30 am
- Location: Lower Central NYS
Re: Cast bullets in 45/70 problem
rock-steady wrote:[Does your Marlin have microgroove rifling???
/quote]
I'm embarrassed to say, I don't know. I will look when I get home. I do know it is an older model with smooth wood and it has the cross-bolt safety.
Should be marked as such!
If not with an unloaded gun looking at the rifling there will be more than the deep 6 grooves(such as usually 12 etc.)
They will also be shallower in depth not deep like the 6 groove ballard!
Re: Cast bullets in 45/70 problem
If I remember correctly, Marlin did use micro groove rifling in the guide gun until just a few years ago. Mine has the ballard type and still doesn't particularly like some of the cast bullets.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
- O.S.O.K.
- Advanced Levergunner
- Posts: 5533
- Joined: Sun Apr 27, 2008 4:15 pm
- Location: Deep in the Piney Woods of Mississippi
Re: Cast bullets in 45/70 problem
Micro groove rifled barrels will shoot cast boolits just fine! They're just more finicky - especially about the diameter. They REALLY want them a tad ovesized...
NRA Endowment Life
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
Re: Cast bullets in 45/70 problem
O.S.O.K., I am not saying that the micro groove doesn't work with cast bullets, just that even with the ballard type rifling, mine is still picky about cast bullets. I have an old Glenfield 60 with the micro groove rifling, and it was great until it had about 85,000 or 90,000 rounds through it. I got an ACCR'RZR tool and it is back to being accurate. I probably wore the rifling down with aggressive cleaning. My Guide gun is accurate with the 350 grain lead round nose, but they are not gas checked and I am getting a little blow-by.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
- rock-steady
- Levergunner 2.0
- Posts: 442
- Joined: Tue Dec 18, 2007 7:35 am
- Location: Deplorable Red State
Re: Cast bullets in 45/70 problem
The rifle in question is a Marlim 1895SS, serial # 12XXXX. It has microgroove rifling. I've been loading the old remington 405 jacketed flat point bullet over H335. I want to work up a reduced load using cast bullets for general plinking and informal target shooting. What should I use to slug the bore?
"People who need long explanations at moments when everything depends on instinct have always irritated me." ~ Guy Sajer
- Borregos
- Advanced Levergunner
- Posts: 4756
- Joined: Thu Sep 13, 2007 7:40 am
- Location: Ontario, Canada
Re: Cast bullets in 45/70 problem
I use pure lead "egg" sinkers from the local tackle shop, lightly oil the bore and pound it through (lightly) with short lengths of dowel.
Pete
Sometimes I wonder if it is worthwhile gnawing through the leather straps to get up in the morning..................
Sometimes I wonder if it is worthwhile gnawing through the leather straps to get up in the morning..................
Re: Cast bullets in 45/70 problem
Short lengths of about 6". If you use long ones and snap one, they get wedged real tight.
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
- rock-steady
- Levergunner 2.0
- Posts: 442
- Joined: Tue Dec 18, 2007 7:35 am
- Location: Deplorable Red State
Re: Cast bullets in 45/70 problem
This is why I love this forum so much. I learn something new all the time. I've been shooting for 42 years, reloading my own ammo for thirty years and casting my own boolits for 1 month...and now I get to slug my first bore!
"People who need long explanations at moments when everything depends on instinct have always irritated me." ~ Guy Sajer
- O.S.O.K.
- Advanced Levergunner
- Posts: 5533
- Joined: Sun Apr 27, 2008 4:15 pm
- Location: Deep in the Piney Woods of Mississippi
Re: Cast bullets in 45/70 problem
If you go with a .460" lead boolit, it should be sufficiently snug... I'm betting you get .457-.458" bore. This means casting your own - unless somebody here knows of a source of .460" comercially cast boolits? If I may - I also recommend Lee's liquid alox lube.
NRA Endowment Life
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
- Old Ranger
- Levergunner 2.0
- Posts: 201
- Joined: Wed Oct 20, 2010 1:44 pm
- Location: East Texas
Re: Cast bullets in 45/70 problem
If my date codeing is correct that would make your rifle a 1988 production.
Microgroove bores are, as the other's said, prone to wanting larger diameter rounds. Case in point; Had a .30-30 with a bore that miked out at a dead on .308". Shot .308" and .309" jacketed stuff all day, but was forced to use a gas checked cast round sized to .312" and then it was on track. In the 45-70 this will be even more pronounced due to the large diameter of the bore/bullet. The radius will be flatter as compared to a 30 cal and such. I agree that even if your bore mikes out to .457" or so, I'd go at least .460" to see if the problem is resolved.
Are you getting leading in the first few inches of the bore with this bullet/load combination? I'm wondering about that as I'm typing this.....
I do hope you get this fixed and you then can enjoy the cast stuff in your rifle!
Wade
Microgroove bores are, as the other's said, prone to wanting larger diameter rounds. Case in point; Had a .30-30 with a bore that miked out at a dead on .308". Shot .308" and .309" jacketed stuff all day, but was forced to use a gas checked cast round sized to .312" and then it was on track. In the 45-70 this will be even more pronounced due to the large diameter of the bore/bullet. The radius will be flatter as compared to a 30 cal and such. I agree that even if your bore mikes out to .457" or so, I'd go at least .460" to see if the problem is resolved.
Are you getting leading in the first few inches of the bore with this bullet/load combination? I'm wondering about that as I'm typing this.....
I do hope you get this fixed and you then can enjoy the cast stuff in your rifle!
Wade
Aim low boys! They're riddin' shetlands!
- sore shoulder
- Advanced Levergunner
- Posts: 2611
- Joined: Sat Sep 15, 2007 4:51 pm
- Location: 9000ft in the Rockies
Re: Cast bullets in 45/70 problem
IIRC the Lee 45-70 molds throw bullets that are way undersized and I think that's because they are designed to be paper patched. I have always used .459-.460 bullets in my Marlins and have had no accuracy issues.
"He has erected a multitude of New Offices, and sent hither swarms of Officers to harass our people and eat out their substance." Declaration of Independance, July 4, 1776
11B30
11B30
Re: Cast bullets in 45/70 problem
No reason for hard lead bullets in the .45-70. Go with dead soft lead, good gooey bullet lube and a slight taper crimp should fix. Most over crimp a 45/70. Up to around 1600 FPS you shouldn't get leading. Lead will fill the rifling properly and you should decent accuracy. Good Luck.
Re: Cast bullets in 45/70 problem
Montana Bullet Works has commercial cast bullets in .460. I know there are other quality companies that offer them also, but I can't think of them off the top of my head. Just FYIO.S.O.K. wrote:If you go with a .460" lead boolit, it should be sufficiently snug... I'm betting you get .457-.458" bore. This means casting your own - unless somebody here knows of a source of .460" comercially cast boolits? If I may - I also recommend Lee's liquid alox lube.
If you have the ability, as you obviously do since you are already casting, I'd just get a .460 sizing die and a new mold if you don't have one that throws them that big and have at it. Much cheaper that way, but there are some really good commercial cast bullets available if you decide to go that route.
"If ye love wealth greater than liberty, the tranquility of servitude greater than the animating contest for freedom, go home from us in peace. We seek not your counsel, nor your arms. Crouch down and lick the hand that feeds you; and may posterity forget that ye were our countrymen" - Samuel Adams
-
- Senior Levergunner
- Posts: 1459
- Joined: Wed Feb 06, 2008 6:31 pm
- Location: Arizona Territory
Re: Cast bullets in 45/70 problem
Get some gas checked bullets, after you slug the bore. They will shoot better in that micro-bore than bare-footed pills.
BTW; You will most likely end up with Gas checks anyway. This you will do when you get tired of mining lead from the bore.
BTW; You will most likely end up with Gas checks anyway. This you will do when you get tired of mining lead from the bore.
SASS# 51223
Arizona Cowboy Shooter's Assoc.
Cowtown Cowboy Shooter's Assoc.
Uberti 73/44-40 carbine, Rossi 92/44-40,
Marlin 94CB/44 24" Limited, Winchester 94/30-30
Arizona Cowboy Shooter's Assoc.
Cowtown Cowboy Shooter's Assoc.
Uberti 73/44-40 carbine, Rossi 92/44-40,
Marlin 94CB/44 24" Limited, Winchester 94/30-30
Re: Cast bullets in 45/70 problem
If you are casting your own and your mold is a bit small, you can lap or Beagle it easily.
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
- rock-steady
- Levergunner 2.0
- Posts: 442
- Joined: Tue Dec 18, 2007 7:35 am
- Location: Deplorable Red State
Re: Cast bullets in 45/70 problem
Tycer, one question about beagling; do you place the silver tape on both halves of the mold?
One good thing about casting is if the bullets aren't acceptable...back in the pot they go!
One good thing about casting is if the bullets aren't acceptable...back in the pot they go!
"People who need long explanations at moments when everything depends on instinct have always irritated me." ~ Guy Sajer
Re: Cast bullets in 45/70 problem
Usually just one, but it really depends on how much you need. Both sides will often leave a parting line, but the sizer fixes that.rock-steady wrote:Tycer, one question about beagling; do you place the silver tape on both halves of the mold?
One good thing about casting is if the bullets aren't acceptable...back in the pot they go!
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
- rock-steady
- Levergunner 2.0
- Posts: 442
- Joined: Tue Dec 18, 2007 7:35 am
- Location: Deplorable Red State
Re: Cast bullets in 45/70 problem
Alright, time to make a new plan. The boolits I cast mike exactly .459". My question is, would a sizer die in .460" size do anything to a .459" boolit? Or do I beagle the mold and then run through the .460 sizer die? Or just look for a .460" mold?
I will slug my barrel this weekend. Thanks for the advice.
I will slug my barrel this weekend. Thanks for the advice.
"People who need long explanations at moments when everything depends on instinct have always irritated me." ~ Guy Sajer