JB-Weld application when COLD...???
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
- AJMD429
- Posting leader...
- Posts: 31937
- Joined: Sun Sep 09, 2007 10:03 am
- Location: Hoosierland
- Contact:
JB-Weld application when COLD...???
Can you apply it in an ambient temperature that is rather cold...? I see nothing about that on their website.
I would 'assume' that the chemical reaction would still happen, but happen more slowly; however I'm sure there are other factors.
I would 'assume' that the chemical reaction would still happen, but happen more slowly; however I'm sure there are other factors.
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
Re: JB-Weld application when COLD...???
If that's a concern, I'd warm the parts and area with a blow dryer or heat gun first, and also maybe "aim it in that area" while it cured too. A propane heather -- used safely of course -- would also help offset any negatives from the c-c-c-cold. Good luck.
Old No7
Old No7
"Freedom and the Second Amendment... One cannot exist without the other." © 2000 DTH
Re: JB-Weld application when COLD...???
If you can mix it, it will cure... eventually.
-
- Advanced Levergunner
- Posts: 5493
- Joined: Mon Apr 02, 2007 9:23 pm
- Location: Batesville,Arkansas
Re: JB-Weld application when COLD...???
Doc are you still working on that wood splitter? I can't begin to think of how many tubes of JBWeld I have gone through.
JerryB II Corinthians 3:17, Now the Lord is that Spirit: and where the Spirit of the Lord is, there is liberty.
JOSHUA 24:15
JOSHUA 24:15
Re: JB-Weld application when COLD...???
Yep as Old No7 said, if ya want it to dry faster heat the area with a hair dryer but not to much or it will run on ya and you`ll sit there with a stick keeping it in place.
It will cure in the cold just take longer.
It will cure in the cold just take longer.
Because I Can, and Have
-------------------------------------------------------------
USAF-72-76
God Bless America.
Disclaimer, not responsible for anyone copying or building anything i make.
Always consult an expert first.
-------------------------------------------------------------
USAF-72-76
God Bless America.
Disclaimer, not responsible for anyone copying or building anything i make.
Always consult an expert first.
-
- Advanced Levergunner
- Posts: 6972
- Joined: Tue Apr 03, 2007 8:52 pm
- Location: Ridgefield WA. USA
Re: JB-Weld application when COLD...???
Epoxy that cures slowly will be stronger than if it cures fast. There is a limit to how much cold they can take though. Sometimes I just put a light bulb near by and cover with something to help contain some of the warmth.
-
- Advanced Levergunner
- Posts: 4296
- Joined: Wed Sep 15, 2010 12:57 pm
- Location: Vinita, I.T.
Re: JB-Weld application when COLD...???
I sometimes use a heat lamp and shine it on from a safe distance. As I recall they say 70 degrees F is a minimum but I know I've used it colder.
M. M. Wright, Sheriff, Green county Arkansas (1860)
Currently living my eternal life.
NRA Life
SASS
ITSASS
Currently living my eternal life.
NRA Life
SASS
ITSASS
- Sixgun
- Posting leader...
- Posts: 18566
- Joined: Sun Sep 16, 2007 7:17 pm
- Location: S.E. Pa. Where The Finest Winchesters & Colts Reside
Re: JB-Weld application when COLD...???
I had this leaky copper pipe in the basement at the fitting that feeds the water for the outdoor hose and it was in an area that I could not get a torch to....I shut the water off and did not feel like waiting a day for the jb weld to cure....so ...after mixing up the jb weld I also mixed up some 2 part liquid epoxy.....the five minute kind........maybe 20% in volume to the jb weld.......mixed the whole shabang together....slopped it on....and in the morning I turned the water back on....no leaks.....
That was about 10 years ago.---6
That was about 10 years ago.---6
Re: JB-Weld application when COLD...???
Not quite the same but I had to make a polyester putty patch on a boat one time during the winter. I mixed it a little hot, put a chem, shake em up hand warmer over it and taped a plastic bag over the whole area.
Cured good overnight, and is still there over 20 years later.
Cured good overnight, and is still there over 20 years later.
Re: JB-Weld application when COLD...???
I usually put a little ceramic space heater on JB Weld or Bondo to cure
'em when it's chilly.
Not that body work outside when it's 35 F is all that much
fun, but a little tarp tent and a space heater at least lets the
stuff cure. Warm the parts a little and put the tubes of goo in
your pocket for a little while to warm 'em up, apply as above
and you're usually good to go for anything epoxy-based.
-Stretch
'em when it's chilly.
Not that body work outside when it's 35 F is all that much
fun, but a little tarp tent and a space heater at least lets the
stuff cure. Warm the parts a little and put the tubes of goo in
your pocket for a little while to warm 'em up, apply as above
and you're usually good to go for anything epoxy-based.
-Stretch
- marlinman93
- Advanced Levergunner
- Posts: 6432
- Joined: Sun Apr 01, 2007 3:40 pm
- Location: Oregon
Re: JB-Weld application when COLD...???
Heat is one of the few things that will make epoxy let go, so be careful not to heat it too high while curing! I've used heat often to warm parts before applying epoxy, but I wouldn't keep the heat on the epoxy unless you keep it far enough away to not get the surface temps over maybe 110 degrees.
If I'm trying to get epoxy off, I use my heat shrink gun to heat it, and it always works, unless it's some special high temperature epoxy.
If I'm trying to get epoxy off, I use my heat shrink gun to heat it, and it always works, unless it's some special high temperature epoxy.
Pre WWI Marlins and Singleshot rifles!
http://members.tripod.com/~OregonArmsCollectors/
http://members.tripod.com/~OregonArmsCollectors/
Re: JB-Weld application when COLD...???
There are many kinds of JB Weld. Chances are they are different. I'd look at your packaging.
The Rotten Fruit Always Hits The Ground First
Proud Life Member Of:
NRA
Second Amendment Foundation
Citizens Committee For The Right To Keep And Bear Arms
DAV
Proud Life Member Of:
NRA
Second Amendment Foundation
Citizens Committee For The Right To Keep And Bear Arms
DAV
Re: JB-Weld application when COLD...???
Well, it's good to 500 F when cured, 600 F
for a VERY short time, and up to a constant
450 F.
Non-Toxic, but they don't advise eating it.
(Anybody having any experience adding it to
their favorite dish, please DO share......)
Microwave safe. Fix the handle on yer favorite
coffee mug..... (Food contact safe ?!)
Like MarlinMan, I would warm things only to
the "warm to the touch" standard while it's curing.
See the FAQ link below....
https://www.jbweld.com/pages/faqs
-Stretch
for a VERY short time, and up to a constant
450 F.
Non-Toxic, but they don't advise eating it.
(Anybody having any experience adding it to
their favorite dish, please DO share......)
Microwave safe. Fix the handle on yer favorite
coffee mug..... (Food contact safe ?!)
Like MarlinMan, I would warm things only to
the "warm to the touch" standard while it's curing.
See the FAQ link below....
https://www.jbweld.com/pages/faqs
-Stretch
Re: JB-Weld application when COLD...???
Heat lamp, or a regular incandescent bulb to keep it just warm enough to cure within 24 hours or thereabouts has worked for me in the past. It will cure in 40 to 50 degree temperatures just fine, just a little slower than at 70 degrees or above.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost