effect of barrel length on velocities
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
effect of barrel length on velocities
Gents I was looking to load about 4-5 grains of titegroup or similar behind a .357 158grain coated hardcast. The manual suggest about 1000-1050fps from a 10" pistol barrel. From a 24" rossi carbine do you think I will get much more velocity or will such a light powder charge be burned up well before that anyway?
Re: effect of barrel length on velocities
With full 357 Mag loads and 158+ grain bullets velocity maxes at 16”. I would therefore surmise the light load would still be subsonic.
Cool website:
http://www.ballisticsbytheinch.com
Cool website:
http://www.ballisticsbytheinch.com
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
Re: effect of barrel length on velocities
Naw I can't believe 16" is maximum. Not saying this 4.5 grain powder load will get any faster... but full powder loads aka 20+ grains maxing out at 16?
Those BBTI charts aren't comparing apples to apples the way I see it. Their 16" gun is a closed breech 94, the 18" gun which is dropping 200fps is a open cylinder stoeger buntline...some of these revolver carbines let a lot of gas out. I had the circuit judge carbine in 22WMR and it was losing near 350fps over same length rifle...
Those BBTI charts aren't comparing apples to apples the way I see it. Their 16" gun is a closed breech 94, the 18" gun which is dropping 200fps is a open cylinder stoeger buntline...some of these revolver carbines let a lot of gas out. I had the circuit judge carbine in 22WMR and it was losing near 350fps over same length rifle...
Re: effect of barrel length on velocities
That’s not from oh it’s by the inch. That’s for my experience using 2400, little gun, it is 16 A 20, and a 24 inch. A combination of 94s and 92
Sorry about the bad grammar, I’m dictating this on my phone
Sorry about the bad grammar, I’m dictating this on my phone
Kind regards,
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
Tycer
----------------------------------------------------------------
http://www.saf.org - https://peakprosperity.com/ - http://www.guntalk.com
- GunnyMack
- Advanced Levergunner
- Posts: 10702
- Joined: Mon Sep 19, 2016 7:57 am
- Location: Not where I want to be!
Re: effect of barrel length on velocities
Most shotgun and pistol powders are done producing around 16-20.
My concern would be the possibility of sticking a bullet in the bore with light loads. I'd try 1 over a chrono and make absolutely certain it leaves the bore.
My concern would be the possibility of sticking a bullet in the bore with light loads. I'd try 1 over a chrono and make absolutely certain it leaves the bore.
BROWN LABS MATTER !!
- Sixgun
- Posting leader...
- Posts: 19243
- Joined: Sun Sep 16, 2007 7:17 pm
- Location: S.E. Pa. Where The Finest Winchesters & Colts Reside
Re: effect of barrel length on velocities
The only thing I can add is that by chronographing several thousand rounds from several 9mm handguns vs. a 16" barreled UZI did not produce enough velocity gain that would mean the difference between lights on or lights off.----6
-
- Advanced Levergunner
- Posts: 4559
- Joined: Fri Sep 07, 2007 1:52 pm
Re: effect of barrel length on velocities
For what it is worth - using a ballistics program only, and certainly not from my personal experience, I get these figures from QuickLoad, below.
I tried a few different 158 grain cast bullets, and results were all similar. However, I cannot account for friction difference in the hard cast bullet you are using from others, so I will just present what I ended up with as a model.
Bullet: .358 cal. 158 grain Speer Lead Semiwadcutter (LSWC) #4623
COAL ("OAL") 1.590"; bullet listed as .660" long
Hodgdon TiteGroup 5.0 gr.
Maximum PSI (PMax) 22805 psi, all loads -
Powder already burned 100% at 6" barrel or less, started at my Python 6" barrel length
10" barrel: 1085fps
16" barrel: 1155fps
24" barrel: 1206fps
Oddly, MV's are the same when I check "Friction Proofed Bullet." Perhaps a coated pistol bullet is too short to make a difference(?)
Again, just throwing out what my ballistics calculator sez.
I tried a few different 158 grain cast bullets, and results were all similar. However, I cannot account for friction difference in the hard cast bullet you are using from others, so I will just present what I ended up with as a model.
Bullet: .358 cal. 158 grain Speer Lead Semiwadcutter (LSWC) #4623
COAL ("OAL") 1.590"; bullet listed as .660" long
Hodgdon TiteGroup 5.0 gr.
Maximum PSI (PMax) 22805 psi, all loads -
Powder already burned 100% at 6" barrel or less, started at my Python 6" barrel length
10" barrel: 1085fps
16" barrel: 1155fps
24" barrel: 1206fps
Oddly, MV's are the same when I check "Friction Proofed Bullet." Perhaps a coated pistol bullet is too short to make a difference(?)
Again, just throwing out what my ballistics calculator sez.
Re: effect of barrel length on velocities
From my own experience I can only say that an AE 158gr JSP chronographs at 1080fps out of my 4" Colt Python and/or GP100 and at 1800fps out of my 18" Marlin 1894C.
Government office attracts the power-mad, yet it's people who just want to be left alone to live life on their own terms who are considered dangerous.
History teaches that it's a small window in which people can fight back before it is too dangerous to fight back.
History teaches that it's a small window in which people can fight back before it is too dangerous to fight back.
Re: effect of barrel length on velocities
Thanks for all the replies. I have a wide variance of advice on different forums. From bullets slowing down to gains of 100, 150fps and 200fps. Persoinally I can't see 200fps being possible but one of the knowedegable fellows I correspond with suggested he gets about 100-120fps gain, which is actually pretty similar to your quickload estimates Johndfresno
As to full power loads, Paco's loads here indicate the bullet is still gaining speed even between 20 to 24", 80fps or so. While 16" may be where the powder is all burned up, the pressure is still enough to keep speeding up the bullet up for quite a bit more length.
But anyway for these light loads of fast burners, which are another subject, I'll bite the bullet and do some chronographing between my 6" pistol and 24" carbine and report back.
As to full power loads, Paco's loads here indicate the bullet is still gaining speed even between 20 to 24", 80fps or so. While 16" may be where the powder is all burned up, the pressure is still enough to keep speeding up the bullet up for quite a bit more length.
But anyway for these light loads of fast burners, which are another subject, I'll bite the bullet and do some chronographing between my 6" pistol and 24" carbine and report back.
- vancelw
- Advanced Levergunner
- Posts: 3950
- Joined: Mon Sep 28, 2009 1:56 pm
- Location: 90% NE Texas and 10% SE Montana
Re: effect of barrel length on velocities
You're going to get broad answers because everyone reads your question with their own bias most of the answers I have seen given to you (on other forums as well) are too narrowly based on that person's own experience with their own favorite powder and their own favorite bullet.mickbr wrote: ↑Tue May 22, 2018 11:58 pm Thanks for all the replies. I have a wide variance of advice on different forums. From bullets slowing down to gains of 100, 150fps and 200fps. Persoinally I can't see 200fps being possible but one of the knowedegable fellows I correspond with suggested he gets about 100-120fps gain, which is actually pretty similar to your quickload estimates Johndfresno
Quickloads is a good research tool to get you started on real life experiences. JohndeFresno and Earlmc have helped a lot of people on this forum with Quickload queries.
"Make yourself an honest man, and then you may be sure that there is one less scoundrel in the world." - Thomas Carlyle
Re: effect of barrel length on velocities
Just for reference, with 6.5gr of Unique behind a 158gr Rainier plated bullet, I get 950 from a 4" S&W 66 and 1350 from a 20" Rossi 92.
Great shooting load, by the way.
Great shooting load, by the way.
"Oh bother", said Pooh, as he chambered another round.
-
- Advanced Levergunner
- Posts: 4559
- Joined: Fri Sep 07, 2007 1:52 pm
Re: effect of barrel length on velocities
I am a huge devotee of QuickLoad, even given the fact that (as Earl and I have both stated) some of the handgun load predictions with certain powders are a bit less accurate than long gun loads.
I attribute the occasional handgun load discrepancy to certain spikey powders and - my theory, at least - that cylinder gap in the revolvers where gas leaks out.
Anyway, QL very closely echoes the above load info, as an example. Remember that firearms, barrels etc. vary, but QuickLoad sure helps me to start out with a reasonable load; very important for a former mountain boy who is stuck in a town several miles from a range or a good shooting area.
The Rainer bullets and of course Unique powders are already in the tables, so no juggling or guesstimating is necessary for this info:
158gr Rainier HP plated bullet, 6.5 gr. Unique, Stated SAAMI Max PSI for .357 is 35000psi (35k); 64.8% fill of the cartridge
4" barrel: 99.35% powder burned, 14485 psi, 940fps MV
20" barrel: 100% powder burned, 23974 psi, 1387fps MV
The problem with Quickload is the price: Currently $152.95 for combined Quickload and Quick target, plus tax and negligible shipping. But that was absorbed long ago - for me - by gasoline savings (about $10 each round trip) and component selections (wrong powder purchases are costly) while working up the particular loads that I wanted.
Re: effect of barrel length on velocities
I found emergency canned food at the farm had expired. Lined em up on the range and had at em with a 3.5 in. Premodel 27, and an 8 in. Python. The Smith put holes in and knocked over the cans. The colt blew em up, split like a bannana,, and found blood spatter 35 feet away behind d the firing line at 21 ft. Great fun and wife went 6 cans in a row with her grandpa's smith. The difference in damage from the two great 357s was an eye opener
Re: effect of barrel length on velocities
thanks all and vance and Johnd, I hear you about quickload. Would it show what powder can get 1200-1250fps with 158 grain with the smallest charge? Thats equal to factory revolver, good load for game where I'm at. Hodgon suggests 5 grains of powders like 700x... I got Hodgon clays and win231 on hand which might do similar.
-
- Advanced Levergunner
- Posts: 4559
- Joined: Fri Sep 07, 2007 1:52 pm
Re: effect of barrel length on velocities
Yes, over fifty powders listed, although you need to verify the raw stats against suggested powders for your firearm. That is, even rifle powders are listed for this load - way over 50 by my quick rough count - that apparently fall within acceptable pressures (below SAAMI max).
One of the lowest charges is this for a 10 inch barrel using the 158gr. Hornady SWC #10408
Alliant POWER PISTOL, 61% fill, 7.0gr., 1250fps, 96.7% propellant burnt, Max PSI 19816
It appears that Hodgdon Clays would be way over pressure of the 35000 SAAMI Max listing.
And your Win 231 is iffy, but if you load up carefully to about 1211 fps (Not 1250) for this load, you SHOULD be stayting within safe limits, per this software’s suggestion. Again, always double check this prediction against other creditable published sources and work up to it. Per QL:
158gr. Hornady SWC #10408, using a 10” barrel
Bullet length is a major factor in getting the right stats;
This listing is for a bullet that is .690” long, COAL 1.590” –
Win 231, 6.2gr. 56.6% fill, 100% burn, 28229 Max PSI, 1211fps
There are many powders that would work better, however. There is a lot of info; I'll PM you after dinner.
Re: effect of barrel length on velocities
Thanks I meant equalling factory levels but with the rifle, so getting 1250fps in a 24" barrel. But thanks for that info you posted its good to know anyway.
-
- Advanced Levergunner
- Posts: 4559
- Joined: Fri Sep 07, 2007 1:52 pm